AS 1984-1977

Table of Contents

1 -  AS 1984-1977 VERNIER CALLIPERS (METRIC SERIES)
4 -  PREFACE
5 -  CONTENTS
6 -  SECTION 1. SCOPE AND GENERAL REQUIREMENTS
6 -  1.1 SCOPE.
6 -  1.2 NOMENCLATURE.
6 -  1.3 DEFINITIONS.
6 -  1.4 STANDARD SIZES.
9 -  1.5 MATERIALS AND PROPERTIES.
9 -  1.5.1 Materials.
9 -  1.5.2 Stabilizing.
9 -  1.5.3 Hardness.
10 -  1.6 FINISH.
10 -  1.7 REFERENCE TEMPERATURE.
10 -  1.8 MARKING.
10 -  1.9 PROTECTION.
10 -  1.9.1 Protective Case.
10 -  1.9.2 Packaging.
11 -  SECTION 2. DESIGN AND DIMENSIONS
11 -  2.1 GENERAL DESIGN REQUIREMENTS.
11 -  2.1.1 General.
11 -  2.1.2 Vernier Callipers Reading to 0,02 mm.
11 -  2.1.3 Vernier Callipers Reading to 0,1 and 0,05 mm.
11 -  2.2. GENERAL DIMENSIONS.
11 -  2.3 MEASURING FACES.
11 -  2.3.1 Faces for External Measurement.
12 -  2.3.2 Faces for Internal Measurement.
13 -  2.4 SCALES.
13 -  2.4.1 General.
13 -  2.4.2 Parallax Error.
16 -  2.4.3. Scale Marks
18 -  SECTION 3. ACCURACY
18 -  3.1 SCOPE OF SECTION.
18 -  3.2 BEAM.
18 -  3.2.1 Straightness of the Principal Guiding Face.
18 -  3.2.2 Flatness of Beam.
18 -  3.3 FACES FOR EXTERNAL MEASUREMENT.
18 -  3.3.1 Flatness.
18 -  3.3.2 Parallelism.
18 -  3.3.3 Squareness of the Fixed Jaw to the Beam (Vernier Callipers Reading to 0.02 mm only)
18 -  3.3.4 Equality of Length of Fixed and Sliding Jaws (Vernier Callipers Reading to 0.02 mm only)
19 -  3.4 FACES FOR INTERNAL MEASUREMENT.
19 -  3.4.1 Cylindrical Faces for Internal Measurement.
19 -  3.4.2 Knife-edge Type of Faces for Internal Measurement
19 -  3.5 INDICATION ERROR (OVERALL ACCURACY).
21 -  APPENDIX A - METHODS OF TEST
21 -  A1 GENERAL.
21 -  A2 FLATNESS OF FACES FOR EXTERNAL MEASUREMENT.
21 -  A3 PARALLELISM OF FACES FOR EXTERNAL MEASUREMENT.
21 -  A4 MAINTENANCE OF PARALLELISM OF FACES FOR EXTERNAL MEASUREMENT DURING CLAMPING OF THE SLIDING JAW
21 -  A5 COMBINED WIDTH OF FACES FOR INTERNAL MEASUREMENT.
21 -  A6 PARALLELISM OF FACES FOR INTERNAL MEASUREMENT.
22 -  A7 THICKNESS OF GRADUATION LINES.
22 -  A8 INDICATION ERROR.

Abstract

Specifies materials, properties, basic design details, accuracy and finish of vernier callipers reading to 0.1 and 0.05 mm in sizes up to 1000 mm and to 0.02 mm in sizes up to 300 mm. An appendix gives notes on the testing of the more important features of the instruments. It does not apply to dial callipers but these callipers may comply except for read-out and indicating mechanism.

Scope

This standard specifies requirements for vernier callipers reading to 0,1 (1/10), 0,05 (1/20), and 0,02 (1/50) mm, and having measuring ranges as given in Table 1.
Requirements for materials and properties, basic design, accuracy and finish are also specified.
NOTE: Notes on methods for testing the more important features of vernier callipers are given in Appendix A. These notes are for guidance only and do not purport to be either recommended or mandatory methods of test.
Although dial callipers are not specified in this standard (see Preface), they should comply with all relevant requirements except those for the read-out and indicating mechanism.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
Pages
ISBN
Committee	ME-027
Supersedes	DR 76012 AS B82-1952