AS 2702-1984

Acoustics - Methods for the measurement of road traffic noise

Standards Australia

More info

1 - AS 2702-1984 ACOUSTICS-METHODS FOR THE MEASUREMENT OF ROAD TRAFFIC NOISE
4 - PREFACE
4 - CONTENTS
5 - 1 SCOPE.
5 - 2 REFERENCED DOCUMENTS.
5 - 3 APPLICATION.
5 - 4 DEFINITIONS.
5 - 4.1 Equi valent continuous A-weighted sound pressure level
5 - 4.2 Percentile level
5 - 4.3 Derived descriptor
5 - 4.4 Vehicle type
7 - 5 INSTRUMENTATION
7 - 5.1 Acoustic instrumentation.
7 - 5.1.1 General.
7 - 5.1.2 Sound level meter.
7 - 5.1.3 Tape recorder.
7 - 5.1.4 Sound level analyser.
7 - 5.1.5 Graphic level recorder and statistical distribution analyser.
7 - 5.1.6 Calibration.
7 - 5.1.7 Field checks.
7 - 5.2 Other instrumentation.
7 - 5.2.1 General.
7 - 5.2.2 Meteorological inst rumentation.
7 - 6 PROCEDURES FOR MEASUREMENT.
7 - 6.1 Site selection.
7 - 6.1.1 General.
8 - 6.1.2 Road impact studies.
8 - 6.1.3 Specific situations.
8 - 6.2 Microphone location.
8 - 6.2.1 General.
8 - 6.2.2 Microphone height.
8 - 6.2.3 Horizontal distance from microphone.
8 - 6.2.4 Distance from reflecting surfaces.
8 - 6.2.5 Microphone location inside buildings.
8 - 6.3 Measurement sampling techniques.
8 - 6.3.1 General.
8 - 6.3.2 Effect of traffic flow rate.
8 - 6.4 Measurement of meteorological factors.
8 - 6.5 Site geometry.
8 - 6.6 Road surface classification.
9 - 6.7 Road traffic parameters.
9 - 6.7.1 Road traffic flow.
9 - 6.7.2 Traffic speed.
9 - 7 REPORTING OF RESULTS.
11 - APPENDIX A - DETERMINATION OF ROAD SURFACE MACROTEXTURE USING THE SANDPATCH TECHNIQUE
11 - A1 GENERAL.
11 - A2 DETERMINATION OF ROAD SURFACE MACROTEXTURE.
12 - APPENDIX B - RESULTS TO BE RECORDED IF INSERTION REQUIRED IN THE NAASRA TRAFFIC NOISE DATA BASE

Abstract

Specifies methods for the measurement of road traffic noise and for the collection of associated data. This Standard outlines also the minimum instrument requirements and the preferred scales of measurements. Explanation is also given for the procedure for selection of measurement sites and the non-acoustic data which are to be recorded in conjunction with the acoustic measurements. This Standard does not include methods of prediction of road traffic noise levels nor of assessment of the effect of traffic noise on people.

Scope

This standard sets out methods for the measurement of the noise emitted by road traffic. The sound pressure levels are expressed in decibels, generally using the A-weighting network.
This standard describes minimum instrument requirements, preferred scales of measurement, and the location of measurement sites and non-acoustic data which are to be recorded in conjunction with the acoustic measurements.
NOTE: While the A-weighting network is usually sufficient for traffic noise studies, it may also be necessary to use frequency analysis or other weighting networks, for specific situations. See AS Z41 for details of octave, half octave and one-third octave band filters used for analysis of sound and AS 1259 for details of other networks.
Some of the methods described and the data to be acquired in this standard are only necessary if the measurements are for research purposes.
This standard does not include methods of prediction of road traffic noise levels nor of assessment of the effect of traffic noise on people.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Pending Revision indicates that as a result of the Aged Standards review process, the document needs updating. If no project proposal, meeting the quality criteria, is received within the 12 month timeframe, the document shall be withdrawn.
Pages
ISBN
Committee	EV-010
Supersedes	DR 82108