AS 2788-2002

Table of Contents

1 -  AS 2788-2002 PNEUMATIC FLUID POWER-GENERAL REQUIREMENTS FOR SYSTEMS (ISO 4414:1998, MOD)
4 -  PREFACE
6 -  CONTENTS
7 -  INTRODUCTION
9 -  1 Scope
9 -  2 Normative references
10 -  3 Definitions
10 -  3.1 actuator:
10 -  3.2 commissioning:
10 -  3.3 component:
10 -  3.4 control mechanism:
10 -  3.5 emergency control:
10 -  3.6 function plate:
10 -  3.7 neutral gas:
10 -  3.8 operating device:
10 -  3.9 piping:
11 -  3.10 pneumatics:
11 -  3.11 purchaser:
11 -  3.12 supplier:
11 -  3.13 system:
11 -  4 Requirements
11 -  4.1 General
11 -  4.1.1 Instructions
11 -  4.1.2 Language*
11 -  4.2 Hazards*
11 -  4.3 Safety requirements
11 -  4.3.1 Design considerations
12 -  4.3.2 Component selection
12 -  4.3.3 Unintended pressures
12 -  4.3.4 Mechanical movements
12 -  4.3.5 Noise
12 -  4.3.6 Leakage
12 -  4.3.7 Airborne hazardous substances
13 -  4.4 System requirements*
13 -  4.5 Site conditions*
13 -  4.5.1 Specifications*
14 -  4.5.2 Drawings*
14 -  5 System design
14 -  5.1 Circuit diagrams
15 -  5.2 Identification
15 -  5.2.1 Components
17 -  5.2.2 Components within a system
17 -  5.2.3 Ports
17 -  5.2.4 Valve control mechanisms
17 -  5.2.5 Internal devices
17 -  5.2.6 Function plates
19 -  5.3 Installation, use and maintenance
19 -  5.3.1 Component replacement
19 -  5.3.2 Maintenance requirements
19 -  5.3.3 Lifting provisions
19 -  5.4 Use of standard parts
19 -  5.5 Seals and sealing devices
20 -  5.6 Maintenance and operating data
20 -  5.7 Operation and maintenance manuals
20 -  6 Energy conversion components
20 -  6.1 Air motors and semi-rotary actuators
20 -  6.1.1 Protection
21 -  6.1.2 Mounting
21 -  6.1.3 Load and speed considerations
21 -  6.2 Cylinders
21 -  6.2.1 Suitability for application
22 -  6.2.2 Mounting and alignment
22 -  6.2.3 Cushions and deceleration devices
23 -  6.2.4 Stroke end stops
23 -  6.2.5 Piston stroke
23 -  6.2.6 Piston rods
23 -  6.2.7 Maintenance
23 -  6.2.8 Single-acting cylinders
23 -  6.3 Surge tanks and other auxiliary reservoirs
24 -  7 Valves
24 -  7.1 Selection
24 -  7.2 Mounting
24 -  7.3 Manifolds
24 -  7.3.1 Surface flatness and finish
24 -  7.3.2 Distortion
24 -  7.3.3 Mounting
25 -  7.3.4 Internal passages
25 -  7.4 Electrically operated valves
25 -  7.4.1 Electrical connections
25 -  7.4.2 Terminal block housing
25 -  7.4.3 Solenoids
25 -  7.4.4 Manual override
26 -  7.5 Valve function identity
26 -  7.6 Relief valves
26 -  7.7 Quick exhaust valves
26 -  8 Conditioning components
26 -  8.1 Filtration
26 -  8.1.1 Filters and separators
26 -  8.1.2 Degree of filtration
26 -  8.1.3 Filter pressures
27 -  8.1.4 Provisions for maintenance
27 -  8.1.5 Location
27 -  8.1.6 Drains
27 -  8.2 Pressure regulation
27 -  8.3 Lubrication
27 -  8.3.1 Lubricating fluids
28 -  8.3.2 Lubricators
28 -  8.3.3 Lubricator filling
28 -  8.4 Shielding
28 -  8.4.1 Non-metallic bowls on fluid conditioning units
28 -  8.4.2 Metallic bowls on fluid conditioning units
29 -  8.5 Air dryers
29 -  9 Piping
29 -  9.1 General requirements
29 -  9.1.1 Fluid flow
31 -  9.1.2 Use of fittings and connections
31 -  9.1.3 Design of layout
31 -  9.1.4 Piping location
31 -  9.1.5 Piping across access ways
31 -  9.2 Pipe and tube requirements*
31 -  9.3 Support of piping
31 -  9.3.1 Spacing
32 -  9.3.2 Installations
32 -  9.3.3 Piping between assemblies
32 -  9.4 Foreign matter
32 -  9.5 Flexible hose assemblies
32 -  9.5.1 Requirements
33 -  9.5.2 Installation
33 -  9.5.3 Protection against failure
33 -  9.6 Quick-action couplings
33 -  9.7 Removal of piping
34 -  10 Control systems
34 -  10.1 Unintended movement
34 -  10.2 System protection
34 -  10.2.1 Supply shut-off valve
34 -  10.2.2 Control or power supply failure
34 -  10.2.3 External loads
34 -  10.3 Components
34 -  10.3.1 Adjustable control mechanism
34 -  10.3.2 Stability
35 -  10.3.3 Tamper resistance
35 -  10.3.4 Manual control levers
35 -  10.3.5 System set up controls
35 -  10.3.6 Two-hand controls
35 -  10.3.7 Spring biased or detent located valves
35 -  10.4 Control systems with servo or proportional valves
36 -  10.5 Other design considerations
36 -  10.5.1 Monitoring of system parameters
36 -  10.5.2 Test points
36 -  10.5.3 Back pressure
36 -  10.5.4 Control of multiple devices
36 -  10.5.5 Sequence control
37 -  10.6 Location of controls
37 -  10.6.1 Protection
37 -  10.6.2 Accessibility
37 -  10.6.3 Manual controls
37 -  10.6.4 Enclosures and compartments
38 -  10.7 Emergency controls
38 -  10.7.1 Features of emergency controls
38 -  10.7.2 System restart
38 -  11 Diagnostics and monitoring
38 -  11.1 Pressure measurement
39 -  11.2 Electrical supply indicators
39 -  12 Cleaning and painting
39 -  13 Preparation for transportation
39 -  13.1 Identification of piping
39 -  13.2 Packaging
39 -  13.3 Protection of openings
39 -  14 Commissioning
39 -  14.1 Verification tests*
40 -  14.2 Noise
40 -  14.3 Fluid leakage*
40 -  14.4 Final data to be provided
40 -  14.5 Modifications*
41 -  15 Identification statement
42 -  Annex A - Items requiring supplier/purchaser agreement
43 -  Annex B - List of hazards
45 -  Annex C - Cross reference list ISO 4414/EN 983
49 -  Annex D - Example of a parts list
50 -  Annex E - Example of pneumatic system data form
57 -  Annex F - Bibliography
59 -  Index
70 -  APPENDIX ZZ - MODIFICATIONS TO ISO 4414:1998 FOR APPLICATION IN AUSTRALIA

Abstract

Specifies requirements for the design and manufacture of pneumatic fluid power systems. This Standard is an adoption with Australian modifications and has been reproduced from ISO 4414:1998.

Scope

This International Standard provides general rules relating to pneumatic systems used in
industrial manufacturing processes. It is intended as a guide for both suppliers and purchasers, with a view to ensuring:
a) safety;
b) uninterrupted system operation;
c) ease and economy of maintenance;
d) long life of the system.
This International Standard does not apply to air compressors and the systems associated with air distribution as typically installed in a factory.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
Pages
ISBN
Committee	ME-035
Supersedes	DR 02244-02245 CP AS 2788-1985 DR 02245 CP