AS 1774.4.5-2002 (R2013)

Table of Contents

1 -  AS 1774.4.5-2002 REFRACTORIES AND REFRACTORY MATERIALS-PHYSICAL TEST METHODS - PREPARATION OF TEST PIECES-GUNNING...
1 -  SECTION 1 SCOPE AND GENERAL
1 -  1.1 SCOPE
1 -  1.2 REFERENCED DOCUMENTS
1 -  1.3 DEFINITIONS
1 -  1.3.1 Activator
1 -  1.3.2 Dry gun assembly
1 -  1.3.3 Plastic gunning mix
2 -  1.3.4 Rebound
2 -  1.4 SAFETY
2 -  1.5 GENERAL APPARATUS
2 -  1.5.1 Air compressor
2 -  1.5.2 Test plate
2 -  1.5.3 Air pressure gauge
2 -  1.5.4 Muffle furnace
2 -  1.5.5 Weighing scale
2 -  1.5.6 Weighing scale
2 -  1.5.7 Drying oven
2 -  1.5.8 Miscellaneous tools
2 -  1.5.9 Thermometer
3 -  1.6 SAMPLING
4 -  SECTION 2 PREPARATION OF TEST PIECES-DRY GUNNING
4 -  2.1 SCOPE
4 -  2.2 PRINCIPLE
4 -  2.3 APPARATUS
4 -  2.3.1 Gun
4 -  2.3.2 Mixer
4 -  2.3.3 Material hose/nozzle assembly
4 -  2.3.4 Water-measuring device (if predamping)
4 -  2.3.5 Water-pressure gauge
4 -  2.4 PROCEDURE
5 -  2.5 PRECISION
5 -  2.6 TEST REPORT
8 -  SECTION 3 PREPARATION OF TEST PIECES-WET GUNNING
8 -  3.1 SCOPE
8 -  3.2 PRINCIPLE
8 -  3.3 APPARATUS
8 -  3.3.1 Pump
8 -  3.3.2 Activator pump
8 -  3.3.3 Mixer
8 -  3.3.4 Gunning hose/nozzle assembly
8 -  3.4 PROCEDURE
9 -  3.5 CALCULATION
9 -  3.6 TEST REPORT
11 -  APPENDIX A - METHOD OF PREDAMPING MATERIAL FOR DRY GUNNING PROCEDURE
12 -  APPENDIX B - DETERMINATION OF TOTAL WATER CONTENT AND REBOUND
12 -  B1 TOTAL WATER CONTENT
12 -  B2 REBOUND

Abstract

Sets out procedures for the preparation of test pieces from refractory materials by dry and wet gunning at ambient temperatures.

RECONFIRMATION NOTICE
Technical Committee MN-007 has reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change.
Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice.
Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 4 April 2013.
The following are represented on Technical Committee MN-007:

Australasian Institute of Mining and Metallurgy
Australian Ceramic Society
Bureau of Steel Manufacturers of Australia
Cement Industry Federation
CSIRO Manufacturing & Materials Technology
Institute of Refractories Engineers
Refractories Manufacturers Association of Australia
The University of New South Wales


To view or download a copy of the reconfirmation notice please go to the reconfirmation link near the top of this page.

Scope

This Standard specifies the procedures for the preparation of test pieces from refractory materials by dry and wet gunning at ambient temperatures.
NOTE: The values obtained from test pieces prepared using this method may not correspond with those obtained from test pieces of the same material prepared at a gunning installation site.
This Standard does not apply to plastic gunning mixes.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Reconfirmed 16-07-2013
Pages
ISBN
Committee	MN-007
Supersedes	DR 02246 CP AS 1774.4.5-1994