AS/NZS 4999:2006

Table of Contents

1 -  AS/NZS 4999:2006 PVC-U MAINTENANCE SHAFTS
4 -  PREFACE
5 -  CONTENTS
6 -  SECTION 1 SCOPE AND GENERAL
6 -  1.1 SCOPE
6 -  1.2 APPLICATION
6 -  1.3 LIMITATIONS
6 -  1.4 REFERENCED DOCUMENTS
7 -  1.5 DEFINITIONS
7 -  1.5.1 Average service temperature
8 -  1.5.2 Effective seal
8 -  1.5.3 Effective sealing length
8 -  1.5.4 Maintenance shaft chamber
8 -  1.5.5 Maintenance shaft (MS)
8 -  1.5.6 Maintenance shaft riser
9 -  SECTION 2 GENERAL REQUIREMENTS
9 -  2.1 GENERAL
9 -  2.2 MATERIAL
9 -  2.3 MATERIAL DATA SHEETS
9 -  2.4 FREEDOM FROM DEFECTS
9 -  2.4.1 General
10 -  2.4.2 Ends
10 -  2.4.3 Joints
10 -  2.5 ELASTOMERIC SEALS
10 -  2.6 SOLVENT CEMENTS
10 -  2.7 PACKAGING, STORAGE AND TRANSPORTATION
11 -  SECTION 3 DESIGN
11 -  3.1 GENERAL
11 -  3.2 ACCESSIBILITY
11 -  3.3 CHAMBER WALL THICKNESS
12 -  3.4 STRUCTURAL INTEGRITY
12 -  3.4.1 General
12 -  3.4.2 Design verification by structural analysis
12 -  3.4.3 Design verification by type test
12 -  3.4.4 Riser and riser joint load resistance
13 -  SECTION 4 MANUFACTURE
13 -  4.1 CONFIGURATIONS
13 -  4.2 DIMENSIONS AND TOLERANCES
13 -  4.2.1 General
13 -  4.2.2 Riser
13 -  4.2.3 Chamber wall thickness
13 -  4.3 WELDING
13 -  4.3.1 General
13 -  4.3.2 Training and certification
15 -  SECTION 5 PERFORMANCE REQUIREMENTS
15 -  5.1 GENERAL
15 -  5.2 ACCESSIBILITY TEST
15 -  5.3 WELDED JOINTS
16 -  5.4 ELASTOMERIC SEAL JOINTS
16 -  5.4.1 General
16 -  5.4.2 Hydrostatic pressure test
16 -  5.4.3 Liquid infiltration test
16 -  5.4.4 Contact width and pressure
16 -  5.5 VACUUM-PRODUCTION TEST
17 -  SECTION 6 MARKING REQUIREMENTS
17 -  6.1 GENERAL
17 -  6.2 ADDITIONAL MARKING WITH ADHESIVE LABEL
18 -  APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
18 -  A1 SCOPE
18 -  A2 RELEVANCE
18 -  A3 PRODUCT CERTIFICATION
18 -  A4 MINIMUM SAMPLING AND TESTING FREQUENCY PLAN
18 -  A4.1 General
18 -  A4.2 Retesting
19 -  A4.3 Rejection after retest
22 -  APPENDIX B - REQUIREMENTS FOR STRUCTURAL ANALYSIS
22 -  B1 SCOPE
22 -  B2 PRINCIPLE
22 -  B3 REQUIREMENTS
22 -  B4 TEST REPORT
24 -  APPENDIX C - METHOD FOR DESIGN VERIFICATION BY TYPE TESTING
24 -  C1 SCOPE AND GENERAL
24 -  C1.1 Scope
24 -  C1.2 Relevance of test
24 -  C1.3 Preparation of test assemblies
24 -  C2 TEST
24 -  C2.1 Principle
24 -  C2.2 Apparatus
25 -  C2.3 Personnel
25 -  C2.4 Procedure
25 -  C3 TEST REPORT
28 -  APPENDIX D - METHOD FOR VACUUM TESTING
28 -  D1 SCOPE AND GENERAL
28 -  D1.1 Scope
28 -  D1.2 Relevance of test
28 -  D1.3 Preparation of test assemblies
28 -  D2 TEST
28 -  D2.1 Principle
28 -  D2.2 Apparatus
28 -  D2.3 Procedure for vacuum type test
28 -  D2.4 Procedure for vacuum batch release test
29 -  D3 TEST REPORT
29 -  D3.1 Type test report
29 -  D3.2 Batch release test report
30 -  APPENDIX E - METHOD FOR LOAD TESTING
30 -  E1 SCOPE AND GENERAL
30 -  E1.1 Scope
30 -  E1.2 Relevance of test
30 -  E1.3 Preparation of test assemblies
30 -  E2 TEST PROCEDURE
30 -  E2.1 Principle
30 -  E2.2 Apparatus
30 -  E2.3 Procedure
31 -  E3 TEST REPORT

Abstract

Specifies design and manufacture requirements for a PVC-U maintenance shaft (MS) comprising a fabricated or injection-moulded, or both, chamber jointed to an extruded PVC riser.

Scope

This Standard specifies design and manufacture requirements for a PVC-U maintenance shaft (MS) comprising a fabricated or injection-moulded, or both, chamber jointed to an extruded PVC riser.
MSs are intended for installation in sewerage systems (up to DN 300) for transportation of sewage at atmospheric pressure and average service temperatures up to 25 degrees Celsius. They are intended for buried vertical installation at depths up to 6 m, without buckling or collapse and without exceeding specified long-term diametral distortion and stress limits. Long-term design criteria limits are 50-year extrapolated or predicted values. Provided installation and operating conditions conform to the guidelines in this Standard, life expectancy may exceed 50 years.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
Pages
ISBN
Committee	PL-021
Supersedes	AS/NZS 4999(Int):2003