AS 2403-2008

Table of Contents

<toc>
<bookmarktable>
<bookmark index='0'>
<pageno>1</pageno>
<text>AS 2403-2008 METALLIC MATERIALS-SHEET AND STRIP-DETERMINATION OF PLASTIC STRAIN RATIO</text>
<bookmark index='1'>
<pageno>4</pageno>
<text>PREFACE</text>
</bookmark>
<bookmark index='2'>
<pageno>5</pageno>
<text>CONTENTS</text>
</bookmark>
<bookmark index='3'>
<pageno>6</pageno>
<text>1 SCOPE</text>
</bookmark>
<bookmark index='4'>
<pageno>6</pageno>
<text>2 REFERENCED DOCUMENTS</text>
</bookmark>
<bookmark index='5'>
<pageno>6</pageno>
<text>3 DEFINITIONS</text>
<bookmark index='6'>
<pageno>6</pageno>
<text>3.1 Plastic strain ratio r</text>
</bookmark>
<bookmark index='7'>
<pageno>7</pageno>
<text>3.2 Weighted average plastic strain ratio, r</text>
</bookmark>
<bookmark index='8'>
<pageno>7</pageno>
<text>3.3 Degree of planar anisotropy, &#916;r</text>
</bookmark>
</bookmark>
<bookmark index='9'>
<pageno>8</pageno>
<text>4 NOTATION</text>
</bookmark>
<bookmark index='10'>
<pageno>9</pageno>
<text>5 PRINCIPLE</text>
</bookmark>
<bookmark index='11'>
<pageno>9</pageno>
<text>6 TEST EQUIPMENT</text>
</bookmark>
<bookmark index='12'>
<pageno>9</pageno>
<text>7 TEST PIECE</text>
<bookmark index='13'>
<pageno>9</pageno>
<text>7.1 Type and preparation</text>
</bookmark>
<bookmark index='14'>
<pageno>9</pageno>
<text>7.2 Thickness</text>
</bookmark>
<bookmark index='15'>
<pageno>9</pageno>
<text>7.3 Surface</text>
</bookmark>
<bookmark index='16'>
<pageno>9</pageno>
<text>7.4 Longitudinal axis</text>
</bookmark>
<bookmark index='17'>
<pageno>9</pageno>
<text>7.5 Reduced section test pieces</text>
</bookmark>
<bookmark index='18'>
<pageno>9</pageno>
<text>7.6 Parallel test pieces</text>
</bookmark>
</bookmark>
<bookmark index='19'>
<pageno>10</pageno>
<text>8 PROCEDURE</text>
<bookmark index='20'>
<pageno>10</pageno>
<text>8.1 Testing temperature</text>
</bookmark>
<bookmark index='21'>
<pageno>10</pageno>
<text>8.2 Manual assessment</text>
</bookmark>
<bookmark index='22'>
<pageno>10</pageno>
<text>8.3 Automatic measurement</text>
</bookmark>
<bookmark index='23'>
<pageno>10</pageno>
<text>8.4 Strain rate</text>
</bookmark>
<bookmark index='24'>
<pageno>10</pageno>
<text>8.5 Applied strain rate</text>
</bookmark>
<bookmark index='25'>
<pageno>10</pageno>
<text>8.6 Strain level</text>
</bookmark>
<bookmark index='26'>
<pageno>10</pageno>
<text>8.7 Measuring gauge length and width (manual determination)</text>
</bookmark>
<bookmark index='27'>
<pageno>10</pageno>
<text>8.8 Measuring gauge length and width (automatic determination)</text>
</bookmark>
<bookmark index='28'>
<pageno>10</pageno>
<text>8.9 Invalid test</text>
</bookmark>
<bookmark index='29'>
<pageno>10</pageno>
<text>8.10 Non-homogeneous plastic strain</text>
</bookmark>
<bookmark index='30'>
<pageno>10</pageno>
<text>8.11 Coated materials</text>
</bookmark>
</bookmark>
<bookmark index='31'>
<pageno>11</pageno>
<text>9 EXPRESSION OF RESULTS</text>
<bookmark index='32'>
<pageno>11</pageno>
<text>9.1 Manual determination</text>
</bookmark>
<bookmark index='33'>
<pageno>11</pageno>
<text>9.2 Homogeneous deforming behaviour</text>
</bookmark>
<bookmark index='34'>
<pageno>13</pageno>
<text>9.3 Calculated values</text>
</bookmark>
<bookmark index='35'>
<pageno>13</pageno>
<text>9.4 Difference between automatic and manual determination</text>
</bookmark>
</bookmark>
<bookmark index='36'>
<pageno>13</pageno>
<text>10 TEST REPORT</text>
</bookmark>
</bookmark>
</bookmarktable>
</toc>

Abstract

Specifies a method for determining the plastic ratio of flat products (sheet and strip) made of metallic materials.

Scope

This Standard specifies a method for determining the plastic strain ratio of flat products (sheet and strip) made of metallic materials.

General Product Information

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
Pages
ISBN
Committee	MT-006
Supersedes	DR 07121 AS 2403-1980